Magazines:  Real Estate Shopping: Adult Costumes  |  Kids Costumes  |  Car Books  |  Guitars |  Electronics
This Issue Archived Articles Blog About Us Contact Us
SEARCH


Upgrading to LED Interior Lighting

Easy, quick and cheap!

by Julian Edgar

Click on pics to view larger images

At a glance...

  • Direct connection to 12V
  • No polarity
  • Very bright but low power consumption
  • Massive illumination upgrade
  • Simple installation
Email a friend     Print article

High intensity LED lighting has been one of the technical revolutions of the last decade. Filament lamps, that in general purpose lighting have reigned supreme for something like a century, are now being replaced by LEDs.

Click for larger image

But using high power LEDs has never been as simple as using filament lamps - what with the need to control current by a dropping resistor or a (more efficient but much more expensive) DC:DC converter. Take the replacement of an interior car light, for example. By the time you source a LED of sufficient intensity and organise and position a dropping resistor, it’s a project that very rapidly loses appeal!

OK, so why this preamble? We recently came across a new LED-based bulb. It costs AUD$21 and it’s been developed to replace the power-hungry miniature MR16 halogen lights that are widely used in shop and domestic installations. In fact, electrically and physically, it’s a direct drop-in replacement. That means it will work off the 12V power supply in a car. You don’t even have to worry about polarity – just wire it straight in.

The light draws only about 100 milliamps at 12V and 170 milliamps at 13.8V – very low current consumption indeed. In fact, as a comparison, that’s only about one-third the power draw of a typical interior light bulb. But does that make it really dim? Nope – in fact the LED bulb is far brighter. That’s the case for two reasons: (1) it’s much more efficient at turning electricity into light, and (2), all the light is aimed in the right direction!

Not only is the LED replacement brighter and uses less power, it also stays much cooler. Finally in the list of advantages, the light output is much less yellow so things look better when illuminated by the LED light.

OK, so how do you install one of these beasts?

Installation

Click for larger image

The LED light provides an even and fairly wide beam. In addition to car interior lighting, it would work very well as a general purpose bike headlight or handheld torch.

Click for larger image

We chose to upgrade the hatchback lighting of this Honda. The new LED light, complete with its pins, is 45mm deep, so keep in mind the required rear clearance. (The other major dimension is diameter – it’s 50mm.)

Click for larger image

A small screwdriver was used to pop out the lens...

Click for larger image

...and then the body of the light itself could be removed.

Click for larger image

A piece of grained ABS plastic was cut out and to provide better rearwards clearance, a short section of rubber hose was glued to it. The LED light was glued into the tube.

Click for larger image

The wiring was then connected. I had available a suitable connection block but if you don’t, solder straight to the lamp’s pins or use crimp-on terminals. Insulate the connections.

Click for larger image

The panel was held in place with a little more glue.

Job finished!

Results

Click for larger image

The results are stunning – so much more light comes from the LED assembly that it makes the original look like a feeble, yellow glow-worm....

Where to Buy

The AutoSpeed shop has a limited number of the lamps – see MR16 Type 12V DC Multi LED Lamp. They’re also available at specialist lighting and electronics stores.

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
Making plans

DIY Tech Features - 24 January, 2012

A New Home Workshop, Part 2

Laying out a home workshop - and storage options

DIY Tech Features - 30 September, 2008

Building a Home Workshop, Part 8

Do hybrid cars make sense?

Technical Features - 16 October, 2007

Alternative Cars, Part 6 - Hybrid

Building a programmable temperature alarm

DIY Tech Features - 13 October, 2009

eLabtronics EZ System, Part 2

Electronic module that can sound high or low temperature alarms or warnings

DIY Tech Features - 30 June, 2008

The eLabtronics Pulser, Part 2

Building and installing the in-wall speakers

DIY Tech Features - 11 December, 2012

Sound in the Lounge, Part 3

There are good technical reasons why steam could return

Technical Features - 9 October, 2007

Alternative Cars, Part 5 - Steam

Steps in mixing and matching front brake components

DIY Tech Features - 29 May, 2012

Selecting components for upsized front brakes

How Chrysler developed a 2.4 litre turbo

Technical Features - 5 July, 2003

Designing a Factory Turbo Engine

Aerodynamic testing techniques for near zero cost

DIY Tech Features - 7 April, 2009

Ultimate DIY Automotive Modification Tool-Kit, Part 2

Copyright © 1996-2017 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip